• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat doblo van remote key 500 Key Fob Won't Work

A key fob from fiat 500 spare key cost 500 is a handy way to unlock the doors and start the car. However, there are numerous reasons why the fob may stop working. This includes a dead battery water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for your vehicle). Includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why the 500 key fob won't function is due to the battery is dead. Modern key fobs have a limited operating range and should be within a few feet of the vehicle to function. If you are far from your car and press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one from a reputable brand such as Panasonic Duracell or Energizer. You can usually find them at your local hardware store, or online.

After you've replaced the coin cell battery, you can test it by standing next to your fiat 124 spider key fob Cover 500 and pressing the buttons. The car will flash its parking lights and the key fob should operate the lock and unlock buttons.

If the fob's remote doesn't function after replacing the battery, it may have water damage that stops it from connecting to the receiver module inside your vehicle. Water damage can happen in a variety of ways, from an accidental splash to submerging the fob in salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture back out. If this does not work, you'll need to have the fob replaced by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean or wash it in a machine. Saltwater can cause the circuit board to short, and eventually end up dying. In the event that you let your fob get wet, it's not an option, but if you drop it in a glass of water or forget to take it out of your pants pocket before running the washing machine Don't give up hope.

First, remove the battery. Before replacing the battery clean the electronic chip with isopropyl or similar products. Test the fob next to check if it's functioning. If the key does not function, it may need to be reset. This is usually done by an auto locksmith or dealer.

If your key is older and not programmed to work with your vehicle You will need to replace it completely. This is a simple process which can be accomplished by a professional locksmith for automotive use. The locksmith will require the key cut to match your vehicle's ignition. They will also need to reprogram the fob to the system of your car. This is a quick and cost-effective procedure that is usually completed the next day.

Receiver Module Issues

The 500 key fob you have may not function because it's out of range. The remote has a range of 30 feet. Therefore, should you be too far away from your vehicle it won't be able to respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If you've replaced your coin battery (commonly known as a "button" or "watch") and the fob isn't working, it could have an internal circuit board issue. In the majority of cases, reprogramming your fob can resolve the issue. You can find directions on how to start a fiat 500x with key to do this for all automobiles by searching YouTube or consulting the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they lose tension, it could prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob may be out of alignment with your vehicle because due to hardware or software issues. This can cause a major headache, but you can usually resolve this issue by visiting a local dealer or auto locksmith to have them reprogram your fob. In some instances the software may require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This can happen when the key fob is near an electronic radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. The key fob may not function because of a weak connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. battery replacement, reprogramming and using the spare key fob, you could have a damaged receiver module on your 500. The receiver module, located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It transforms the signals into electronic commands which are then processed by the vehicle.

There's a simple method to reset the 500's internal system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then reconnect the battery. This will eliminate any remaining electricity, and restart the car's computer. This will help you get your key fob to work again. If the problem persists you should consult an expert technician. They will be able to determine the exact cause of any issues.