• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your replacement fiat 500 key key duplication; similar webpage, 500 Key Fob Won't Work

A key fob for the Fiat 500 allows you to easily open doors and start your vehicle. There are many reasons why the fob won't work. These include a dead coin battery damage to the receiver module, water issues, and interference.

This listing is for a NEW replacement fiat 500 key Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is an inactive battery. Modern key fobs come with a limited operating range and should be within just a few feet of the vehicle to operate. If you are far from your vehicle when you press the key fob button the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one of a trusted brand like Panasonic Duracell or Energizer. You can find them at the local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The car should blink its parking lights, and the key fob should work the lock and unlock switches.

If your fob's key doesn't work even after replacing the battery, there may be water damage which is preventing it from connecting to the module inside your vehicle. Water damage can happen in a variety of ways, from the slightest splash to submerging the fob salt water at the beach. If you believe your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this doesn't work, you will require your fob to be changed by an auto locksmith or dealer.

Water Damage

The fob does have rubber seals to keep water from the chip's electronic circuit and out of the ocean or washing it in a machine could cause water damage. Saltwater is particularly dangerous to the circuit board of the fob and can cause it to short out and eventually end up dying. Getting the fob wet is not an ideal idea, but if you drop it in a glass of water or don't remember to remove it from your pocket before you run the washer, don't give up hope.

First remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or a similar product. Check the fob again to check if it's working. If the key still doesn't work, it may have to be changed. This is typically handled by a professional or dealer auto locksmith.

If your key is old and has not been programmed to work with your vehicle it is necessary to replace it completely. A professional locksmith in the automotive industry can carry out this simple task. The locksmith will need the key cut to match your car's ignition. They will also need to reprogram the fob for the car's system. This is a low-cost and quick procedure that can be completed the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far away from your car it will not respond to your commands. This can be easily fixed by moving closer to your vehicle until it starts responding.

If your fob does not work after you replace the battery inside the coin, which is also called a "button", "watch" or "button" It could be a problem with the internal circuit board. Reprogramming your fob can resolve this issue. You can find the instructions for most vehicles on YouTube or in the owner's manual.

You may need to replace the metal retaining clips that keep the battery of your coin in place. If they loose tension they could stop the coin battery from being properly seated and cause your remote to malfunction.

In rare cases the fob may be out of the vehicle's sync because due to hardware or software issues. This can be a major headache, but you can usually fix it by visiting an auto locksmith to have them reprogram your fob for you. In some cases, they may need to reinstall the software on your body control module too.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This could happen when the keyfob's location is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob might not work because of a problem to the buttons or water damage, or damage to the internal chips.

If the key fob has been unable to function for a while without notice and you've tried every option at home how to get a new fiat 500 key resolve it e.g. You might have a damaged 500 receiver module if you've tried replacing the battery, reprogramming or using a spare key fiat 500 key fob. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy way to reset all of the onboard systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then, reconnect the battery. This will clear out any remaining electricity and then restart the car's computers. This could help the key fob to function again. If the issue persists you should seek out an expert technician. They can identify the root cause of your issues.