• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, patio doors undergo wear and tear that can lead to lock malfunctions. There are fortunately, a number of easy and efficient methods that can restore your uPVC patio glass Repair door's security.

These simple fixes will ensure your home is secure regardless of whether you re-align the lock or clean the locking mechanism.

Clean the Lock

Patio doors are ideal for bringing the outdoors inside and keeping out the elements. However they could pose risky for security if the lock doesn't work properly. Over time, wear, tear, cold and hot weather dirt and debris can cause your patio door lock to become difficult to operate. With a little maintenance, you can ensure your patio door's locks always function properly.

It is important to first clean the patio door lock and all moving parts. This helps flush out any accumulated grime and coatings that could hinder the lock from functioning as it should. Start by wiping down all the moving parts of your patio door's lock using a damp cloth. then use a scouring pad or rough damp cloth to scrub the hard-to-reach parts of the door and frame that are covered in dirt. It is recommended to wipe the entire lock with dry cloths to eliminate any remaining dampness, and allow it to air dry prior to applying it to the next time.

If your patio door uses pin-tumbler locks, you can apply powdered Graphite on the key. You can also apply a Teflon lubricant like WD-40 Multi Use Product. This type of lubricant is easy to apply and it doesn't dissolve with time. If you're not able to locate an appropriate lubricant, you could try using a pencil that has a thick tip. Insert the pencil in the lock, then shake it around to spread the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors free from dirt, dust and debris. These tracks can be especially vulnerable to snow and ice which can cause them to become stuck or slack which makes it difficult for your patio doors to open and close.

Clean the track rails and rollers on sliding patio doors by removing any weather stripping that is damaged or dirty. Clean it, then replace it. The rollers of patio doors can be cleaned and sprayed down with a nonstick lubricant.

Lubricate the moving parts

uPVC french doors, like sliding glass patio door repair patio doors, work by using 3-4 or sometimes 5-point locking mechanisms which include the lock cylinder and handle operated by a key. These doors require maintenance, oiling of the moving parts. This can be done using an oil that is thin (never WD40) and is recommended to be done at least once per year.

If sagging hinges aren't a cause, the door could be skewed and catch or striking the strike plate hole within the frame. The solution is to take off the strike plate, and then use an abrasive chisel, which will enlarge the mortise it rests in. This will allow the latch to fit into the hole, and prevent it from scratching against the frame.

Take a measurement of the width of the cylinder with the help of a piece of wood or a book that fits into the gap above the adjustment screw. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the Lock's Width

If your patio door latch is difficult to turn even after cleaning and lubricating, there's a possibility that it is out of alignment with the strike plate hole. Verify that the door is in a balanced position, and if the hinge screws are secure. In a lot of cases, moving the strike plate downwards or upwards could solve the issue.

The latch might not work properly when the strike of the lock is not large enough. In this case you'll have to increase the hole using either a hammer or chisel, and then test the latch to make sure that it connects to the strike plate smoothly without rubbing against or getting caught on the frame of the door jamb.

You must identify the kind of mortise lock that you have before purchasing an alternative. You can do this by looking at the faceplate on the lock and determining if it is round or square. Take a look at each screw hole on the existing lock and note their dimensions. This information will allow you to find an alternative lock that is exactly the same width and will fit in the hole you have already.

In addition to identifying the mortise lock that is currently in use, you should also examine it for any scratches or bends that might require repair. A damaged or bent latch is more likely break than one that hasn't been frequently used, so be sure to replace the lock with a new one that is secure when you spot any indications of damage or wear.

Once you've decided on the kind of lock replacement that you require It's time to start the actual repair patio door lock. The old spindle and handle must be removed from the doorway to the patio. Insert the new handle. Begin by installing the interior handle by aligning it with the spindle and then securing it by using the two bolts or screws that secure it. Once the interior handle is installed, put in the handle on the outside and screw it in the position as well. After you've completed these steps Test the handles to make sure that they are able to open and close easily and that the latch engages properly with the strikeplate.

Make sure the door's strike is checked

The strike plate and the door latch are two parts that work together in order to secure the door. Misaligned strike plate and door latches will result in the latch not being able to latch the door in a proper manner. Fortunately, the issue is usually simple to fix.

Check the holes for receiving of the strike plate to make sure they are clear of obstructions such as dirt or plastic plugs. Then loosen the keeper screws that secure the strike plate in place and allow it to move horizontally, but not detaching it from the frame of the door. Then, you can adjust the strike plate to ensure that its holes for receiving are aligned with the latch hooks on the door latch. Once the strike plate is adjusted tighten the screws, and then test the door to determine whether it locks smoothly after the new adjustment.

Door strike plates can be a bit difficult to locate for homeowners with sliding glass patio door repair patio doors, however they're essential to lock and unlock your door. These metal plates are usually located at the top and bottom of the door jamb, where they support the door's latch. The door latch slides onto this strike plate and creates the seal. If the strike plate is damaged, rusted or not installed correctly, it may hinder the latch from locking the door securely.

The most common reason for an outdoor door lock to stick or not close is a misalignment of the latch and strike plate. The easiest method to check for this is to perform the "lipstick test." Rub some lipstick on the outside of the deadbolt and put masking tape on it. When you close the door, the lipstick will leave marks on the tape, indicating you exactly where the latch meets the strike plate. If the mark is too low or high it is possible to adjust the strike plate.

The sliding patio door locks protect your home from burglars, and if they're not functioning properly, you need to solve the issue fast. By following these simple steps, you'll be able to fix your patio door's lock and regain its functionality in a matter of minutes.