• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat 500 key cover 500 Key Fob Won't Work

A key fob for the fiat key fob replacement 500 is a convenient method to unlock the doors and start the car. There are a myriad of reasons the fob won't work. This could be due to a dead coin battery damaged receiver module, water damage issues, and interfering.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that must be professionally programmed by a local locksmith (click here for Locksmith Search). It includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is due to the battery is dead. Key fobs of today have a limited range of operation and must be within a few inches of the vehicle to work. If you are far from your vehicle, and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a new key for fiat 500 one of a trusted brand such as Panasonic Duracell or Energizer. You can find them in your local hardware store, or online.

After you've replaced the coin cell battery, you can test it by standing in front of your fiat punto Replacement key 500 and pressing the buttons. The parking lights should blink and the key fob will operate the lock and unlock switch.

If your key fob still doesn't work even after replacing the battery, it might be water damage that is preventing it from communicating with the module inside your vehicle. Water damage can occur in a variety of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you think your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If that doesn't work, your fob is likely to require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

The fob does have rubber seals that keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to become shorted and eventually fail. It's not a good thing to get the fob wet however, don't give it up if you accidentally drop it in water or fail to remove it from your pants pocket.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Test the fob afterward to check if it's functioning. If the key doesn't work, it may have to be programmed again. This is usually done by a professional or dealer auto locksmith.

If the key is newer and has never been programmed to your vehicle It is likely that it needs to be replaced completely. This is a simple procedure that can be carried out by a professional locksmith for automotive use. The locksmith will need the key cut to match your vehicle's ignition. They will also need to reprogram the fob in the car's system. This is a cheap and quick process that could be completed the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote usually has 30 feet of range or less and if it's far from your car, it will not respond to your commands. It is possible to remedy this by moving your remote closer to your car until it responds.

If your fob does not work after you replace the coin battery, also called a "button", "watch" or "button", it could be due to an issue with the circuit board inside. In most cases, reprogramming the fob will fix the problem. You can find instructions on how to do this for all automobiles by searching YouTube or consulting the owner's manual.

It's possible that you need to replace the metal clips that keep the battery of your coin in place. If they lose tension, it could prevent the coin battery from being properly seated and can result in the malfunction of your remote.

In rare cases the fob can become out of connection with your vehicle as a result of software or hardware problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain situations they might need to reinstall the software in your body control module too.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This can occur when the keyfob's location is in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob could not function because of a weak connection with the buttons water damage or damage to the internal chips.

If the key fob been unable to function for a while out of the blue or even after trying everything you can do at home to fix it e.g. You may have a faulty 500 receiver module if you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.

Luckily, there is an easy method of resetting all of the onboard systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car's computers, which could help get your key fob working again. If the issue continues, you should consult an expert technician. They will be able to determine the exact cause of issues.