• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How a Wood Burning Stove Works

Wood-burning stoves can be an excellent addition to any home. They should only be made use of properly seasoned wood.

Older stoves with no secondary combustion allowed air to pass through over and below the fuel. This resulted in the loss of energy, chimney tarring and www.913875.Xyz atmospheric pollution.

Modern wood stoves employ a superior combustion principle that splits air supply into two stages. This allows for more efficient heating while reducing emissions.

Efficient Combustion

The efficiency of the combustion of the wood stove is a measure of how well your wood is turned into heat. The efficiency of the heating transfer is the amount that heat is transferred from your stove to the room. A wood-burning stove that has high efficiency and combustion will use less fuel, and generate less waste such as steam and carbon monoxide.

Modern wood stoves boast high efficiency in combustion, due to their sophisticated design. They maximize the amount of heat while using less wood. They also tend to have low emission levels, especially with EPA certified stoves that require a specific catalytic combustor, which cleans the exhaust gases when they leave the stove. These cleaner stoves are a good option for homeowners who wish to minimize their impact on the environment while still enjoying the warmth of a wood stove.

Proper operation and maintenance can improve the efficiency of your stove. The most important aspect is to ensure the combustion process is controlled, which is achieved by maintaining a proper fire in the stove with regular additions of small pieces of wood regularly. This will prevent the accumulation of flammable Creosote in the chimney, which could cause the stove to become less efficient.

Another crucial aspect in the efficiency of wood stoves is the use of properly dried, seasoned firewood that has an average moisture content of less than 20%. Dry well-seasoned and seasoned wood will not only generate more heat from the same fuel, but will also cause less smoke and air pollution.

The Environmental Protection Agency (EPA) has set guidelines to limit the amount smoke and other pollutants an appliance can release in an hour. The majority of modern wood stoves depend on a secondary combustion, or catalytic combustor to reduce pollution and 913875.xyz to meet EPA guidelines. If you're looking to purchase a wood burning stove that complies with EPA emission standards, search for one that has an EPA certification sticker. It should also have a smoke emission rate below 4 grams per hr.

Catalytic Combustion

Catalytic woodstoves make use of a honeycomb combustor made of ceramic that is coated with noble metals, such as palladium or platin. The combustor functions similarly to the catalyst in your car that cleans the exhaust. When smoke passes through the combustor, at high temperatures, the noble metals react with particulates and chemicals in the smoke to break them down into harmless products like carbon dioxide and water.

This allows the stove to emit less carbon dioxide and burn cleaner than non-catalytic models, without loss of efficiency or heat output. The combustor operates most efficiently when the temperature of gas in the flue is 1,000degF or more. If the fire is burnt at a low temperature the gases in the stove don't reach this temperature and the combustor isn't functioning properly.

The combustor could be damaged by burning foreign substances like trash, paper logs painted or treated wood. The burning of these substances can result in "masking" which blankets the combustor cells with a substance which prevents it from functioning in the way it was intended. Masking may also result from closing the bypass damper to soon or refueling with wet wood. If the combustor cells aren't cleaned regularly of creosote, 913875.xyz fly-ash and tar, a plugging could occur, which can cause smoke to leak out.

Properly operated and positioned the combustor will operate to provide years of efficient performance. It will require little maintenance, other than cleaning the soot off its surface after a prolonged burn and regularly cleaning it with a dry, soft bristled brush.

The combustor comes with a bypass damper which is open to start an ignition and shut to load the stove. Check the bypass for the "operate catalyst" indicator, which will indicate when your combustor operates within its optimal temperature range. The operating range of your combustor will be decreased if you close the bypass damper prematurely. Closing the bypass damper too soon can reduce the temperature of the inlet to the combustor and may damage it. Refer to the manual for your stove's instructions on how to operate the damper. You can also reach our customer service department if you require assistance.

Airflow Controls

Controlling air flow is essential to ensure that your wood stove burns safely and efficiently. The primary, secondary and tertiary systems all work together to ensure that your fire is burning efficiently. Each air system plays a distinct role in the combustion process.

The main air control is situated beneath or inside the stove's door. It regulates the amount of air that is able to enter the firebox. More air means a faster-burning fire, but it also increases the risk of creosote and chimney smokiness buildup. Ideally, the air control should be opened for a short time when lighting your wood stove.

After your fire has built up enough heat, the main air control can be shut down slowly until you're satisfied with the amount of heat produced. It is essential to ensure that no smoke is emitted from the chimney or stove since this could indicate an inefficient combustion.

Secondary airflow controls feeds oxygen to the top of your stove, usually in the form of air jets that are placed above your fire. This is the most important aspect of controlling the flame. Without it the fire will burn too quickly and will produce an excessive amount of smoke.

The tertiary airflow, which is the final stage of the airflow system of your stove is fed into the chimney or updraft. This creates a strong draft in the flue, which allows your fire to perform optimally.

It is crucial to remember that the wood stove you have was designed and optimized for burning wood that is firewood only. Any other type of combustion fuel will not be able to burn in your wood stove and can cause high levels of emissions and potentially chimney fires. Softwood is also acceptable however, seasoned hardwood needs to be dried for a minimum of 6 months. Avoid using cardboard and paper since they could release toxic fumes or cause creosote and 913875 ash to build within your stove. You should also avoid placing logs or any other combustibles over your fire, as they could explode.

Safety

Wood-burning stoves are an excellent alternative to electricity, particularly when your area is susceptible to frequent power outages. However, they can be dangerous if used incorrectly. They can result in harmful chemical substances that could be harmful to your health. They may also create a fire hazard and carbon monoxide poisoning. You can stay clear of these risks by implementing a few basic safety measures.

Use only clean, dry wood for your wood-burning stove. Do not use gasoline, kerosene, charcoal starter fluid, wrapping paper or other flammable substances to start or rekindle a flame. Never burn painted or treated wood. Keep the flue open so that you can let plenty of oxygen into. Add wood in small amounts and don't let the fire smolder. If you live in a smoke-control zone, never set up an indoor Www.913875.Xyz [913875.Xyz] fire.

Make sure your chimney and stove are properly installed. A poorly installed wood stove can ignite a fire in the chimney that could release toxic gasses into your home. Regularly checking and cleaning the chimney is also essential. Ensure that the flue is not flowing, which could lead to carbon monoxide poisoning.

Place your wood in a shed, or under a cover. This will help the wood to dry out and get into the season quicker. To reduce the risk of fire, keep the wood from other sources of heat. It is also a good idea to set your stove on a non-flammable area, like tiles.

If you have children, be sure to keep them away from the stove. They might try to play with the hot ash or touch the flame which could be dangerous. Additionally, you should keep all flammable items at least three feet from the stove. Consider installing a heat shield to shield walls and surfaces from damage. It's also an excellent idea to have your family practice home fire drills. This will allow you to escape your home in the event of an emergency. For more information on how to keep your home safe take a look at our article on escape routes to a fire in the event of a home fire.