• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat ducato remote key replacement 500 Key Fob Won't Work

A key fob with the fiat punto key replacement 500 number is a convenient method to open the doors and start the car. However, there are a variety of reasons why the key fob might stop working. This includes a dead coin-battery and water damage, as well as receiver modules issues, and interference.

This listing is for a NEW replacement fiat key cutting Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths in the automotive industry). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not functioning. Modern key fobs have a limited range of operation, and must be within just a few feet of the vehicle to operate. If you are not within your car and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one of a trusted brand like Panasonic Duracell or Energizer. You can typically find them in your local hardware store, or online.

You can test the battery of your coin-cell by pressing the buttons while you are standing close to your fiat key fob programming 500. The car will flash its parking lights, and the key fob should operate the lock and unlock switches.

If your fob's key isn't working even after replacing the battery, there might be water damage that is preventing it from communicating with the module inside your vehicle. Water damage can occur in many ways, such as an easy splash or submerging the key fob saltwater at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to draw the moisture back out. If this does not work, you'll need to have the fob changed by an auto locksmith or a dealer.

Water Damage

The fob does have rubber seals to keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually fail. The fob getting wet is not an ideal idea but if you drop it into a glass of water or don't remember to take it out of your pocket before you run the washing machine, don't give up hope.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Check the fob to check if it's functioning. If the key doesn't function, it may need to be reset. This is usually done by a professional or dealer auto locksmith.

If the key is older and hasn't been programmed to your car it is likely to need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will require the key to be cut to match the car's ignition. The locksmith also needs to reprogram your fob in the car's system. This is a simple and cost-effective procedure that is usually completed in the next day.

Receiver Module Issues

Your fiat 500 remote key key fob may not work because it's out of range. The remote usually has 30 feet of range or less and if it's far away from your car it will not respond to your commands. This can be fixed by moving it closer to your vehicle until it starts responding.

If you've replaced the battery in your coin (commonly known as a "button" or "watch") and the fob isn't working it could be due to an internal circuit board problem. In most cases, reprogramming the fob will solve the issue. You can find instructions on how do i get a spare key for my fiat 500 to do this on the majority of automobiles by searching YouTube or looking through the owner's manual.

It is possible to replace the metal retaining clips that keep the battery of your coin in place. If they lose tension it can prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob may be out of alignment with your vehicle because of hardware or software problems. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations, they may need to reinstall the software on your body control module too.

Interference

Interference can also cause the key fob to not receive or transmit signals. This could occur if the key fob is located near a radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob could not function due to a bad connection to the buttons, water damage or damage to the internal chips.

If the key fob has stopped working one day without notice and you've tried everything you can do at home to fix it e.g. replacing the battery, reprogramming it and using the spare key fob, you could have a defective receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands which are then read by the vehicle.

Luckily, there is an easy way to reset all of the onboard systems in your 500 and include the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then, reconnect the battery. This will erase any remaining electricity, and allow you to restart the computer in your car. This can help get your key fob to function again. If the issue persists, you should speak with an expert technician. They can identify the exact cause of any problems.